View SP8802_283017.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SP8802
3.3GHZ / 2 Fixed Modulus Divider Advance Information
DS2111 ISSUE 7.2 June 1999
Features
G G G G G G G G
Ordering Information
SP8802/A/DG Military temperature range DES9066101/AC/DGAZ (SMD)
Very High Speed Operation 3.3GHz Silicon Technology for low Phase Noise (Typically better than -140dBc/Hz at 10kHz) Specified Over the Full Military Temperature Range Low Power Dissipation 420mW (typ) 5V Single Supply Operation High Input Sensitivity Very Wide Operating Frequency Range Available as DESC SMD 5962-9066101MPA
Thermal Characteristics
ja = 150C/W jc = 50C/W
Description Absolute Maximum Ratings
The SP8802 is one of a range of very high speed low power prescalers for professional and military applications. The device features a complementary output stage with on chip current source for the emitter follower outputs Supply voltage VCC Clock Input voltage Storage temperature range Junction temperature
SUPPLY 1 VCC VREF (2V) 400 400 7 /2 6 INPUT INPUT 2 3 10mA 6.75mA 2mA OUTPUT OUTPUT 500 500
6.5V 2.5V p-p -65C to +150C +175C
5 GND
Figure 1 SP8802 Block diagram
SP8802
Advance Information
INPUT INPUT NC
2 3 4
SP8802
VCC
1
8 7 6 5
NC OUTPUT OUTPUT GND
DG8
Figure 2 Pin connections
Electrical Characteristics
Guaranteed over the temperature range T amb -55C to +125C (see note) and supply voltage range 4.75V to 5.25V. Tested at Tamb = -55C and +100C, VCC = 4.75V and 5.25V. Characteristic
Supply current Input sensitivity 0.65GHz to 2.8GHz 3.3GHz Input impedance (series equivalent) Output Voltage with fin = 1000MHz Output Voltage with fin = 3GHz
NOTE: Devices must be used with a suitable heatsink to maintain chip temperature below 175C when operating at Tamb>100C.
500
400
VIN (mV RMS INTO 50 OHMS)
300
200
100
;;; ;;;
1 2, 3 2, 3 6, 7 6, 7 0.8 50 2 1 0.35 mA mV mV pF Vp-p Vp-p VCC = 5V RMS sinewave measured in 50 ohm system. See Figs. 3 & 4 VCC = 5V VCC = 5V load as Fig. 4
Pin
Min
Value Typ 84
Max 100 175 400
Units
Conditions
*
GUARANTEED* OPERATING WINDOW
Tested as specified in Table of electrical characteristics
1
2
3
4
FREQUENCY (GHz)
Figure 3 Typical input sensitivity
2
Advance Information
SP8802
SIGNAL GENERATOR COAXIAL SWITCH 50 +5V 1 1n 2 8 7
50
POWER METER FROM OUTPUT
0.1
470
3p
SP8802
3 0.1 1n 4 6 5
RATIO COUNTER
OUTPUT LOAD FOR AMPLITUDE MEASUREMENTS
Figure 4 Test circuit
Figure 5 Typical input impedance
3
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2002, Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of SP8802

	To Download SP8802 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .